Contents
Kitchenaid Dishwasher Clean Light Blinking is an indication that there is an error code. This error code specifically means that your dishwasher is failing to heat the water within the allotted time. When the clean light blinks, it is important to troubleshoot the issue in order to get your dishwasher back to working condition.
Please Read this article completely to find out the solution.
Common Causes Of The Clean Light Flashing Error
The KitchenAid dishwasher clean light blinking is actually an error code indicating that the dishwasher is failing to heat the water in the allotted time. This error can be caused by various issues, but the first step to troubleshoot is to reset the control board.
Make sure to check for any potential problems with the water temperature or detergent being used.
When it comes to the clean light flashing error on your Kitchenaid dishwasher, it is important to understand the common causes behind this issue. By identifying these causes, you can troubleshoot and resolve the problem quickly. Here are the main factors that can lead to the clean light flashing error:
1. Using Wrong Type Of Detergent
Using the wrong type of detergent in your dishwasher can trigger the clean light flashing error. This is because certain detergents may not be compatible with your dishwasher’s cleaning cycle. It is essential to use dishwasher-specific detergents that are recommended by the manufacturer. These detergents are formulated to work effectively with the dishwasher’s heating system and water temperature.
2. Water Temperature Issues
Inadequate water temperature can also cause the clean light to flash on your Kitchenaid dishwasher. Dishwashers require hot water to effectively clean and sanitize your dishes. If the water temperature is too low, the dishwasher may not be able to heat the water within the specified time, triggering the clean light flashing error. Ensure that your dishwasher is connected to a hot water supply and check that the water temperature is set to the appropriate level.
3. Other Possible Causes
In addition to using the wrong detergent and water temperature issues, there are other potential causes for the clean light flashing error on your Kitchenaid dishwasher. These include:
- Clogged filters or spray arms that hinder water flow
- Malfunctioning heating element
- Door latch problems
- Control board issues
If you have checked the detergent and water temperature but are still experiencing the clean light flashing error, it is recommended to inspect these other components and seek professional assistance if needed.
How To Troubleshoot The Clean Light Flashing Error
The clean light flashing on your Kitchenaid dishwasher is actually an error code that indicates a failure to heat the water within the allotted time. This error can be caused by several issues, but the first step in troubleshooting is to reset the control board. Here are some steps you can take to troubleshoot the clean light flashing error on your Kitchenaid dishwasher:
Check The Type Of Detergent Being Used
One common cause of the clean light flashing error is using the wrong type of detergent. Kitchenaid dishwashers require a specific type of detergent that is designed for use in dishwashers. Using regular dish soap or hand soap can cause excessive sudsing or poor cleaning performance, leading to the clean light flashing error. Make sure you are using the recommended dishwasher detergent to avoid this issue.
Verify Water Temperature And Adjust If Necessary
An incorrect water temperature can also trigger the clean light flashing error. The dishwasher relies on hot water to effectively clean and sanitize your dishes. Check the water temperature at your kitchen sink and ensure it is set to a minimum of 120°F (49°C) for optimal dishwasher performance. If the water temperature is too low, adjust your hot water heater accordingly.
Check For Other Possible Causes And Solutions
If checking the detergent type and water temperature does not resolve the clean light flashing error, there may be other underlying causes. Here are some other possible causes and solutions to consider:
- Check for a clogged spray arm or blocked filters. Clean or replace as necessary.
- Inspect the dishwasher’s heating element for any signs of damage or malfunction. If found, replace the heating element.
- Ensure the dishwasher door is securely closed and latched. An improperly closed door can disrupt the wash cycle.
- Check the dishwasher’s float switch and float assembly for any blockages or malfunctions. Clean or replace if necessary.
- Reset the dishwasher’s control panel by pressing the sequence of high temp, heat dry, high temp, heat dry buttons on the control panel.
If none of these solutions resolve the clean light flashing error, it may be necessary to contact a professional appliance repair technician for further assistance.
Fixing A Kitchenaid Dishwasher With A Blinking Clean Light
If you own a KitchenAid dishwasher and notice that the clean light on the control panel is blinking, don’t panic. This blinking light is actually an error code indicating that your dishwasher is failing to heat the water within the allocated time. While there could be multiple reasons for this error, here are some step-by-step instructions to help you fix the issue and get your dishwasher running smoothly again.
Step-by-step Instructions For Fixing The Error
Follow these steps to troubleshoot and fix the issue:
- Resetting the control board
- Checking and adjusting water temperature
- Other troubleshooting tips and techniques
Resetting The Control Board
The first step in fixing the blinking clean light error is to reset the control board of your KitchenAid dishwasher. This can be done by following these simple instructions:
- Press the High Temp button.
- Press the Heat Dry button.
- Repeat steps 1 and 2, alternating between High Temp and Heat Dry, within six seconds.
- Close the dishwasher door and wait for the control board to reset.
Checking And Adjusting Water Temperature
If resetting the control board doesn’t resolve the issue, the next step is to check and adjust the water temperature. Here’s what you need to do:
- Make sure that the hot water supply to the dishwasher is turned on and providing sufficient water pressure.
- Verify that the water temperature is set to the recommended range (typically between 120°F and 140°F or 49°C and 60°C).
- If necessary, adjust the water heater temperature to achieve the desired range.
Other Troubleshooting Tips And Techniques
If the issue persists, try the following troubleshooting tips and techniques:
- Check for any obstructions in the dishwasher’s spray arm, filter, or drain hose. Clean or remove any debris found.
- Ensure that the dishwasher door is fully closed and securely latched. If the door is not closing properly, it may prevent the dishwasher from running a cycle.
- Inspect the dishwasher’s float switch and float assembly for any signs of damage or malfunction. Replace any faulty components as necessary.
- Consider using a different type of dishwasher detergent, as using the wrong detergent might cause issues with the dishwasher’s performance.
By following these step-by-step instructions and troubleshooting tips, you should be able to fix the blinking clean light error on your KitchenAid dishwasher. Remember to always consult the manufacturer’s manual or seek professional assistance if you are unsure or uncomfortable performing any repairs yourself. Happy dishwashing!
When To Seek Professional Help
If you have tried all the DIY troubleshooting steps for your KitchenAid dishwasher but the clean light is still blinking, it may be time to seek professional help. Here are some situations where contacting KitchenAid customer support or a professional technician is recommended:
When DIY Troubleshooting Steps Fail
If you have followed the user manual or online tutorials to troubleshoot the clean light blinking issue, but it persists, it indicates a more complex problem that may require the expertise of a professional technician. They have the necessary knowledge and tools to diagnose and fix the underlying issue.
Contacting KitchenAid Customer Support Or A Professional Technician
Contacting KitchenAid customer support is a good first step when encountering persistent issues with your dishwasher. They can provide guidance over the phone and may be able to resolve the problem without the need for a technician visit.
However, if the problem persists or if your dishwasher is under warranty, it is advisable to schedule a service call with a professional technician. They can thoroughly inspect and diagnose the dishwasher to ensure proper repair.
Costs And Considerations For Professional Repair
Before scheduling a service call, it is important to consider the costs involved. Professional repairs can range from a service fee to the cost of replacement parts and labor. The technician will provide a detailed estimate of the repair costs upfront, allowing you to make an informed decision. Additionally, ensure to check if your dishwasher is still under warranty, as some repairs may be covered.
Seeking professional help for your KitchenAid dishwasher clean light blinking issue is recommended when DIY troubleshooting steps fail or when the problem persists. Contacting KitchenAid customer support or scheduling a service call with a professional technician will help resolve the issue efficiently and restore your dishwasher’s functionality.
Frequently Asked Questions
Why Is The Light Blinking On My Kitchenaid Dishwasher?
The blinking light on your KitchenAid dishwasher indicates an error code. This means that the dishwasher is failing to heat the water within a certain time frame. Reset the control board to resolve the issue. It could be caused by various factors, such as using the wrong detergent or a problem with the water temperature.
Check for these issues and reset the dishwasher to clear the error code.
How Do You Reset The Blinking Light On A Kitchenaid Dishwasher?
To reset the blinking light on a KitchenAid dishwasher, follow these steps:
Press the high temp, heat dry, high temp, heat dry buttons on the control panel. This will reset the control board.
If the issue persists, check for problems with water flow, the water valve, or the float device.
Why Is My Kitchenaid Dishwasher Blinking Clean Light 8 Times?
The KitchenAid dishwasher blinking clean light 8 times is actually an error code. It means that the dishwasher is failing to heat the water in an allotted time. This error can be caused by various issues, but the first thing to try is resetting the control board.
How Do You Reset The Clean On A Kitchenaid Dishwasher?
To reset the clean light on a KitchenAid dishwasher, follow these steps:
- Press the High Temp and Heat Dry buttons one after the other.
- Repeat this button sequence: High Temp, Heat Dry, High Temp, Heat Dry.
- The control panel should reset, and the clean light will stop blinking.
Ensure there are no issues with water supply or excess suds in the dishwasher.
Why Is The Kitchenaid Dishwasher’s “clean” Light Blinking?
The blinking “Clean” light on your Kitchenaid dishwasher indicates an error code, typically related to a failure to heat the water within the expected time.
Conclusion
If you find that the clean light on your Kitchenaid dishwasher is blinking, it is likely an error code indicating a problem with heating the water. This can be caused by various issues, but a simple reset of the control board is often the first step to try.
Make sure to use the right detergent and check for any water flow issues that may trigger the float device. If the problem persists, it may be time to seek professional assistance.